Same day or next day service
£No hidden costs
Fully insured
365 day guarantee*
Nationwide
Telford

No Hot Water in Telford

Losing hot water at home is disruptive, and the cause varies considerably depending on the type of heating system your property has.

Call us on 01952 000000 (placeholder - not in service)
Illustrative stock photograph of bathroom basins; not a Telford customer job.

No Hot Water

Losing hot water at home is disruptive, and the cause varies considerably depending on the type of heating system your property has. For homes with a combination boiler, the fault may lie with the boiler itself — a failed diverter valve, a faulty pressure sensor, a blocked heat exchanger, or an ignition problem can all interrupt the hot water supply without affecting the central heating.

In properties with a traditional system boiler and separate hot water cylinder, the issue might be with the cylinder thermostat, a failed immersion heater element, or a motorised valve that is not diverting heated water to the cylinder correctly. Before calling a plumber, a few basic checks are worth carrying out: confirm the boiler is powered on and not in lockout mode, check the system pressure gauge is within the range marked on the boiler (usually between 1 and 1.5 bar when cold), verify the programmer or timer is set correctly, and check whether the boiler is displaying an error or fault code.

If a power cut has recently occurred, some boilers require a manual reset before they will fire again. If basic checks do not resolve the problem, a plumber or heating engineer carries out a more detailed assessment — testing the thermostat, checking the diverter valve operation, inspecting the cylinder and associated valves, and verifying the programmer settings match the intended schedule.

Some faults require the replacement of a specific component, while others involve a service to clear scale build-up inside the heat exchanger. Telford's water supply characteristics can contribute to scale accumulation in boilers over time, which is worth considering in older systems that have not been recently serviced.

Signs Your Hot Water System Needs Attention

⚠️

Lukewarm Water Only

If your hot taps produce water that is warm rather than properly hot, this can indicate a failing thermostat, a partially blocked or scaled heat exchanger, or a diverter valve that is not switching fully between heating and hot water modes.

⚠️

Boiler Lockout or Repeated Error Codes

Modern boilers display fault codes when they detect a problem and shut down to prevent further damage. A boiler that locks out repeatedly after being reset is indicating a fault that needs diagnosing — not simply a transient error to clear.

⚠️

Hot Water Works but Heating Does Not, or Vice Versa

When only one function of a combination boiler stops working, this often points to a fault in the component that manages the split between heating and hot water — such as a diverter valve or a motorised valve — rather than a failure of the boiler burner itself.

How a No Hot Water Assessment Works

1

System Type Identification

The engineer first establishes whether the property has a combination boiler, a system boiler with a hot water cylinder, or a gravity-fed traditional setup, as the diagnostic steps differ significantly between these configurations.

2

Controls and Pressure Check

The engineer checks the programmer and thermostat settings, confirms the boiler pressure is within range, and checks any error codes displayed, ruling out simple causes such as incorrect timer settings or low pressure before opening the boiler.

3

Component Testing and Diagnosis

Key components — including the diverter valve, thermostat, motorised valves, immersion element where present, and heat exchanger — are tested to isolate the fault. The engineer then advises on the repair or replacement options available.

FAQs About No Hot Water

Why has my combination boiler stopped producing hot water but the radiators still heat up?
In a combination boiler, this is often caused by a faulty diverter valve. The diverter valve switches between sending heated water to the central heating circuit and to the hot water taps. If it fails in the heating position, radiators continue to work but hot taps run cold. A plumber or heating engineer can test the valve and replace it if necessary.
My boiler shows an error code and has locked out — should I reset it?
Many boilers can be reset once to clear a transient fault. Look up the specific error code in your boiler manual before resetting, as some codes indicate faults that should not simply be cleared without investigation. If the boiler locks out again after resetting, the underlying fault needs diagnosing properly.
How can I tell if my immersion heater has failed?
If your property has a hot water cylinder with an immersion heater and the water stays cold even when the immersion is switched on for several hours, the element may have failed. A plumber can test the element with a multimeter and replace it if it has blown — this is a straightforward repair in most cases.
What information should I gather before contacting a plumber about a loss of hot water?
Note the type of heating system your property has, whether it is a combination boiler, a system boiler with a cylinder, or a gravity-fed tank and cylinder arrangement. Check whether hot water has stopped completely or is only lukewarm, and whether the central heating is also affected. If your boiler is displaying an error code, note the code before it resets. Knowing the approximate age of the boiler or cylinder, and whether any work has recently been carried out on the system, can also help the plumber identify the likely cause before attending.
My hot water runs warm briefly at the tap and then turns cold. What might cause this?
On a combination boiler, a brief period of warm water that quickly cools can indicate a failing heat exchanger, a restricted flow rate through the primary circuit, or a diverter valve that is not directing flow correctly to the hot water side. On a cylinder system, it may suggest that the cylinder thermostat is cutting off heat prematurely, or that there is stratification of hot and cold water within the cylinder. Describing how long the warm water lasts and whether the problem worsens when multiple outlets are running simultaneously will help a plumber or heating engineer assess the likely cause.
What are the signs that a hot water cylinder thermostat may have failed?
If your hot water cylinder is being heated but the water is consistently lukewarm rather than reaching a normal usable temperature, the thermostat controlling the cylinder may have failed at a low setting. Conversely, water that is significantly hotter than usual could indicate a thermostat that is no longer limiting temperature correctly. Either condition warrants inspection by a qualified plumber or heating engineer, and the latter in particular should be assessed promptly for safety reasons.

More Emergency Plumber services

Burst Pipe RepairWater Leak RepairEmergency Plumber Cost

Other services in Telford

🕳️ Blocked Drains & Drainage 🚰 Tap & Toilet Repairs 💧 Leak Detection & Pipe Repairs 🌡️ Radiator & Central Heating 🚿 Bathroom Plumbing

Related guides

What to do when you find a water leak in Telford

Plumbing Services Across Telford

Request a Free Quote

Tell us what you need and we'll get back to you with a no-obligation quote.

01952 000000 (placeholder - not in service)
Use the enquiry form; the telephone number is a placeholder.
Covering Telford and surrounding areas

Quick quote request

📞 Call Now 💬 Enquire